Продукция

QPHY-SAS2

QPHY-SAS2

The Teledyne LeCroy QPHY-SAS2 Test Solution provides automated control for the SDA 8 Zi series of oscilloscopes for performing all of the transmitter physical layer tests as described by version 1.01 of the UNH IOL Serial Attached SCSI (SAS) Consortium SAS-2 6Gb/s Physical Layer Test Suite. This specification covers targets and initiators running at 1.5 Gb/s, 3.0 Gb/s and 6.0 Gb/s.
QPHY-BroadR-Reach Automotive Ethernet enables faster data communication to meet the demands of today’s vehicles and the connected vehicles of the future. QPHY-BroadR-Reach automates testing and validation of 100 Mb/s Automotive Ethernet, which is described in both the BroadR-Reach and 100Base-T1 (IEEE 802.3bw) specifications.
DDR Debug Toolkit The DDR Debug Toolkit provides test, debug and analysis tools for the entire DDR design cycle. The unique DDR analysis capabilities provide automatic Read and Write burst separation, bursted data jitter analysis and DDR-specific measurement parameters.
ET-PMT Electrical Telecom Mask Test Package
GRL-USB-PD GRL-USB-PD software provides a simple and efficient way to perform USB-PD electrical parametric and protocol measurements. GRL-USB-PD provides waveform visibility and protocol analysis making it ideal for design and debug of USB Type-C Power Delivery silicon and end products.
GRL-USB-PD-C1 GRL-USB-PD-C1 is a flexible test controller, designed for USB-PD Compliance testing of the Unit Under Test (UUT) and more.
LNES Low Noise Edge Shaper
QPHY-10GBase-KR The Teledyne LeCroy QPHY-10GBase-KR solution automates testing for 10Gigabite Ethernet Copper Backplane base on the IEEE 802.3ap specifications. The test framework simplifies the test setup and execution of generic and common test requirements such as jitter separation, rise/fall time and transmitter equalization parameters. The guided wizard prompts the user to for specification required patterns and takes the measurements accordingly. The test report includes the test results pass/fail summary, margins and limits, as well as waveforms and measurements used during the test process.
QPHY-10GBASE-T QPHY-10GBASE-T automated compliance test software performs electrical compliance testing of the Physical Media Attachment (PMA) for 10GBASE-T Ethernet PHY, based on IEEE802.3-2008 requirements.
QPHY-DDR2 The Teledyne LeCroy QPHY-DDR2 Test Solution is the best way to characterize DDR2 memory interfaces. Capable of performing measurements on 400 MHz, 533 MHz, 667 MHz, 800 MHz, 1066 MHz and custom speed grades, QPHY-DDR2 has a full suite of Clock, Electrical and Timing tests as specified by the JEDEC Specification and Intel JEDEC Specifications Addendums.
QPHY-DDR3 The Teledyne LeCroy QPHY-DDR3 Test Solution is the best way to characterize DDR3, DDR3L, and LPDDR3 memory interfaces. Capable of performing measurements on 800 MT/s, 1066 MT/s, 1333 MT/s, 1600 MT/s, 1866 MT/s, 2133 MT/s and custom speed grades, QPHY-DDR3 has a full suite of Clock, Electrical, and Timing tests as specified by the JEDEC Specification.
QPHY-DDR4 DDR4 is an evolutionary upgrade from DDR3. It introduces data transfer rates which are nearly double the DDR3 transfer rates, ranging from 1.6 GT/s up to 3.2 GT/s. DDR4's higher transfer rates and lower operating voltage have driven new test methodologies and test requirements which were not previously required for DDR3 in order to ensure proper signal fidelity. QPHY-DDR4 has a full suite of Clock, Electrical, and Timing tests as specified by the JEDEC Specification which will aid in DDR4 design validation.
QPHY-DisplayPort The QPHY-DisplayPort software option provides an automated test environment for running all of the normative real-time oscilloscope tests for sources in accordance with Version 1.2b of the Video Electronics Standards Association (VESA) DisplayPort PHY Compliance Test Specification, as well as tests for HBR3 signals at 8.1 Gbps.
QPHY-eDP QPHY-eDP provides a highly automated and easy-to-use solution for Embedded DisplayPort source testing in accordance with version 1.4 of the VESA Embedded DisplayPort PHY compliance test guideline.
QPHY-ENET Ethernet testing compliant with IEEE 802.3-2005 requires many test setups and connections and mask tests. Using Teledyne LeCroy QualiPHY-ENET these measurements are easy to setup and complete. Instructive connection diagrams and message boxes appear as pop ups on the oscilloscope screen. The connection diagram instructs the user how to change test fixture and jumper pins in order to do complete test. When the tests are complete, QualiPHY will generate a test report in PDF, HTML, or XML formats. Jitter and pulse mask tests are performed with automatic waveform alignment, and all test results feature pass/fail indicators corresponding to the standard being tested.
QPHY-HDMI2 automated and easy-to-use solution for HDMI transmitter testing in accordance with Version 2.0 of the HDMI Compliance Test Specification (including testing for version 1.4 devices).
QPHY-LPDDR2 The Teledyne LeCroy QPHY-LPDDR2 Test Solution is the best way to characterize LPDDR2 memory interfaces. Capable of performing measurements on 466 MHz, 533 MHz, 667 MHz, 800 MHz, 900 Mhz, 1066 MHz and custom speed grades, QPHY-LPDDR2 has a full suite of Clock, Electrical and Timing tests as specified by the JEDEC Specifications.
QPHY-MIPI-DPHY - D-PHY Compliance Package Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the MIPI Alliance Specification for D-PHY version 1.00.00
QPHY-MIPI-MPHY The QPHY-MIPI-MPHY Test Solution provides automated control of Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the MIPI Alliance Specification for M-PHY version 3.0.
QPHY-MOST150 The Teledyne LeCroy QPHY-MOST150 compliance test package provides a highly automated and easy-to-use solution to MOST compliance testing. QPHY-MOST150 will perform all electrical compliance tests as defined in the MOST150 oPHY Automotive Physical Layer Sub-Specification Rev. 1.1 and MOST150 cPHY Automotive Physical Layer Sub-Specification Rev 1.0.
QPHY-MOST50 The Teledyne LeCroy QPHY-MOST50 compliance test package provides a highly automated and easy-to-use solution to MOST compliance testing. QPHY-MOST50 will perform all electrical compliance tests as defined in the MOST Electrical Physical Layer Specification Rev. 1.1.
QPHY-PCIe The Teledyne LeCroy QPHY-PCIe Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing the entire transmitter physical layer tests as described by the Card Electro-mechanical specification Rev 1.1 and 2.0
QPHY-PCIe3 Teledyne LeCroy QPHY-PCIe3 Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the PCI Express Base Specification Revision 3.0 Version 0.9 and the Card Electromechanical Specification Revision 3.0 Version 0.7.
QPHY-SAS2 The Teledyne LeCroy QPHY-SAS2 Test Solution provides automated control for the SDA 8 Zi series of oscilloscopes for performing all of the transmitter physical layer tests as described by version 1.01 of the UNH IOL Serial Attached SCSI (SAS) Consortium SAS-2 6Gb/s Physical Layer Test Suite. This specification covers targets and initiators running at 1.5 Gb/s, 3.0 Gb/s and 6.0 Gb/s.
QPHY-SAS3 The QPHY-SAS3 Test Solution provides automated control of the SDA 8 Zi-A and LabMaster 10 Zi oscilloscopes for performing all of the transmitter physical layer tests as described by the T10 SAS-3 specification. This specification covers targets and initiators running at 1.5 Gb/s, 3.0 Gb/s, 6.0 Gb/s, and 12.0 Gb/s.
QPHY-SATA-TSG-RSG for SATA compliance testing to be used in conjunction with the PeRT3. By leveraging the capabilities of both the oscilloscope and the PeRT3, QPHY-SATA-TSG-RSG can automatically perform all of the PHY, TSG, OOB, and RSG tests as described by the SATA UTD 1.5. Furthermore, QPHY-SATA-TSG can be configured to test Gen1, Gen2, and Gen3 SATA PUTs.
QPHY-SFI The Teledyne LeCroy QPHY-SFI solution automates testing for SFI base on the SFF 8431 specifications. The test framework simplifies the test setup and execution of generic and common test requirements such as jitter separation, rise/fall time and transmitter equalization parameters. The guided wizard prompts the user to for specification required patterns and takes the measurements accordingly. The test report includes the test results pass/fail summary, margins and limits, as well as waveforms and measurements used during the test process.
QPHY-USB The USB package provides a complete acquisition and analysis system for USB 2.0 devices, hosts, and hubs, as specified in the USB-IF USB 2.0 Electrical Test Specification. The test software implements a full set of electrical tests for USB 2.0, including High-, Full-, and Low-speed tests and is supported by Teledyne LeCroy’s QualiPHY automated test and reporting software.
QPHY-USB3-Tx-Rx SuperSpeed USB is one of most highly anticipated standards in several years. At 10x the data rate of USB 2.0 and with new features like CTLE (continuous time linear equalization) and reference channels, SuperSpeed USB will pose new challenges to implementers.
QPHY-USB3.1-Tx-Rx QPHY-USB3.1-Tx-Rx offers an automated test package for USB 3.1 transmitter and receiver compliance testing, characterization, and debug.
Key Features
  • QPHY-SAS2 provides a highly automated and easy-to-use solution for SAS-2 configurations from 1.5 Gb/s to 6 Gb/s
  • Compliant with version 1.01 of the UNH IOL Serial Attached SCSI (SAS) Consortium SAS-2 6 Gb/s Physical Layer Test Suite
  • Support for SAS-2 Targets and Initiators
  • QualiPHY automated test framework provides connection diagrams, automated oscillo scope operation and report generation
  • When used in conjunction with the Sierra SAS Protocol Verification System the device or host under test can be stimulated to generate the required test patterns

The Teledyne LeCroy QPHY-SAS2 Test Solution provides automated control for the SDA 8 Zi Series of oscilloscopes for performing all of the transmitter physical layer tests as described by version 1.01 of the UNH IOL Serial Attached SCSI (SAS) Consortium SAS-2 6G b/s Physical Layer Test Suite. This specification covers targets and initiators running at 1.5 Gb/s, 3.0 Gb/s and 6.0 Gb/s.

SAS is the serialized version of the popular SCSI standard. SAS is primarily used for server class storage at speed of up to 6 Gb/s. QPHY-SAS2 covers tests from "Group 1 (TX OOB Signaling and AC Coupling Requirements), Group 2 (TX Spread Spectrum Clocking (SSC) Require ments) and Group 3 (TX NRZ Data Signaling Requirements) of the test specification.

These capabilities make QPHY-SAS2 an all-inclusive automated test suite that meets the requirements for 1.5 Gb/s, 3.0 Gb/s and 6.0 Gb/s Serial Attached SCSI (SAS) transmitter compliance testing.

QPHY-SAS2 provides a highly automated and easy-to-use solution for SAS-2 configurations from 1.5 Gb/s to 6 Gb/s.

Powerful Debugging Tools

The use of Spread Spectrum Clocking (SSC) in transmitted signals is an optional feature of the SAS-2 specification. When SSC is enabled, measurements such as frequency modulation rate and deviation must also be verified per the specification. The QPHY-SAS2 software works in conjunction with the deep memory and powerful analysis library of Teledyne LeCroy oscilloscopes to greatly simplify this verification process. Clock recovery circuitry and clock extraction via Phase-Locked Loops (PLLs) is another significant design consideration. Flexible clock recovery options allow for the replication of virtually any real receiver PLL configuration enabling the simulation of "what if" scenarios. Jitter results can be measured exactly as the receiver would see them.

Out of Band (OOB) validation ensures that the maximum noise during OOB idle, OOB burst amplitude, OOB offset delta, and OOB common mode delta are all within the specification limits.

Spread Spectrum Clock (SSC) validation requires long memory and specialized analysis functions. Teledyne LeCroy is the only manufacturer that can precisely track SSC profiles through multiple cycles in real time. SSC modulation frequency, deviation, balance and DFDT are all measured.

Peak-to-Peak Voltage, VMA and EQ measures the peak-to-peak amplitude, voltage modulation amplitude and transmitter equalization to ensure that these parameters are within the specification limits.

Comprehensive and Easy-to-read Test Reports

Measurement results often need to be summarized and tabulated to quickly verify specifications. This information, together with instrument and signal acquisition/test condition setups, results in a fully documented record. QPHY-SAS2 streamlines this process by incorporating an automatic HTML report generation engine. The created test reports contain tabulated numerical values for each individual test result, including PASS/FAIL and specification limit columns. Reports can also be saved as PDF, HTML or XML.

Connection diagrams prompt the user to set the DUT to output specific test patterns.

Advanced Debug Capability

If a compliance failure is found, Teledyne LeCroy's SDA II serial data analysis package is available to help find the root cause quickly and easily. SDA II has the ability to perform Eye and Jitter measurements simultaneously and is fully integrated into the oscilloscope application software. In addition, SDA II provides insight into the measured Eye and Jitter parameters making it easier to identify the sources of problems.

QualiPHY

QualiPHY is designed to reduce the time, effort and specialized knowledge needed to perform compliance testing on high-speed serial buses.

  • Guides the user through each test setup
  • Performs each measurement in accordance with the relevant test procedure
  • Compares each measured value with the applicable specification limits
  • Fully documents all results
  • QualiPHY helps the user perform testing the right way every time!

Compliance reports contain all of the tested values, the specific test limits and screen captures. Compliance reports can be created as HTML, PDF or XML.

Specifications

QPHY-SAS2 Test Coverage Specifications
TEST 5.1.2 - TX MAXIMUM NOISE DURING OOB IDLE
TEST 5.1.3 - TX OOB BURST AMPLITUDE 
TEST 5.1.4 - TX OOB OFFSET DELTA 
TEST 5.1.5 - TX OOB COMMON MODE DELTA
TEST 5.2.2 - TX SSC MODULATION FREQUENCY 
TEST 5.2.3 - TX SSC MODULATION DEVIATION AND BALANCE
TEST 5.2.4 - TX SSC DFDT (INFORMATIVE
TEST 5.3.1 - TX PHYSICAL LINK RATE LONG TERM STABILITY 
TEST 5.3.2 - TX COMMON MODE RMS VOLTAGE LIMIT 
TEST 5.3.4 - TX PEAK-TO-PEAK VOLTAGE
TEST 5.3.5 - TX VMA AND EQ (INFORMATIVE) 
TEST 5.3.6 - TX RISE AND FALL TIMES
TEST 5.3.7 - TX RANDOM JITTER (RJ) 
TEST 5.3.8 - TX TOTAL JITTER (TJ) 
TEST 5.3.9 - TX WAVEFORM DISTORTION PENALTY (WDP)*
* WDP Test must be run manually using the SASWDP MATLAB script. This is not automated by QPHY-SAS2"
Additional SAS-2 Teledyne LeCroy Test Equipment

The Sierra Protocol Test System is the 6th generation of SAS/SATA protocol test solutions from Teledyne LeCroy, the leading manufacturer of protocol test systems. The PeRT3 (Protocol-enabled Receiver and Transmitter Tolerance Tester) fills the space between physical layer test and protocol test, providing performance testing of receivers and transmitters